Glu/Sense
Dentin Pre-Treatment Desensitizer Gel
Glu/Sense™ HEMA/Glutaraldehyde desensitizer reduces or eliminates post-operative sensitivity by penetrating and sealing dentin tubules and precipating proteins under restorations. Its no-drip formula provides control and accuracy during placement because it stays where it’s placed.
Your orders are filled seamlessly through your preferred dealer.
Get the right product at the right price with the personalized service you trust.
Product Description
Glu/Sense HEMA/Glutaraldehyde desensitizer reduces or eliminates post-operative sensitivity by penetrating and sealing dentin tubules and precipating proteins under restorations. Its no-drip formula provides control and accuracy during placement because it stays where it’s placed. The exclusive SofNeedle with its foam tip enables easy and exact placement and complete coverage of dentin. With its 35% HEMA/5% Glutaraldehyde gel formulation, Glu/Sense acts in seconds to seal out post-op sensitivity. It is compatible with most cements and dentin bonding agents. On etched enamel, Glu/Sense acts as a “wetting agent” helping to prevent collagen fibers from collapsing.
- Treats and seals dentin tubules to prevent post-op sensitivity
- Syringe delivery with SofNeedle foam-tip provides accurate placement with no dripping onto soft tissue
- When used under restorations, effect is permanent.
IDEAL APPLICATIONS:
- Under direct composite restorations with bonding systems
- Under inlays, onlays, crowns and veneers
- Under amalgam restorations
- Made in the USA
Kit contains 6 x 1.0ml syringes + 60 SofNeedle Tips
Specifications
- Unique gel formulation in a syringe, provides control and accuracy with no spills or drips on sensitive tissue
- SofNeedle Applicator
- Foam-tip needle allows for faster, easier placement, without the burning of soft tissue
- Promotes adhesion
- Minimizes microleakage around crowns and restorations
- Works with all bonding agents
How To's
For Syringe Package Application:
- Remove syringe cap and twist on a SofNeedle applicator tip.
- Bend tip, as needed, to gain access to the application site.
- Before use, express a small amount of liquid onto a pad to insure that the material is flowing properly through the SofNeedle application tip.
- After use, remove SofNeedle and discard. Replace cap and disinfect syringe.
DIRECTIONS FOR USE:
Apply Glu/Sense desensitizer to the dentin of the tooth, using a gentle rubbing motion for 30 seconds. Dry and proceed to restoration when indicated. Avoid contact with soft tissue. If contact occurs, flush immediately with water. (See Warning section).
Tooth Preparation:
- Place pulp protection, when necessary, over areas very close to the pulp.
- Dentin does not need to be dry; a moist surface is acceptable.
- Removal of the dentinal smear layer is not necessary. However, if using a dentin-bonding agent that requires “total etch”, remove the smear layer by etching first, and then apply Glu/Sense.
- Dry after applying Glu/Sense with streamof compressed air, followed by thorough rinse and suction.
- Apply each coat for 30 seconds, using a gentle rubbing motion.
- Glu/Sense is compatible with all restorative materials and may be used under composites, cements, glass ionomers and amalgam.
For Cervical Sensitivity (when no restorative material is to be placed):
- Clean surface area with pumice and rinse with water.
- If area is too sensitive to clean with pumice, skip this step and apply the smallest possible amount of Glu/Sense desensitizer in one or two coats. Apply each coat for 30 seconds, using a gentle rubbing motion.
- Dry thoroughly with gentle stream of compressed air until fluid film has disappeared and the surface is no longer shiny. Rinse thoroughly with water.
- Avoid contact with soft tissue. See warning above.
- In extreme cases of dentin hypersensitivity, a dentin bonding agent or varnish may be applied over the Glu/Sense treated dentin.
Cautions:
Glu/Sense dentin desensitizer should only be used by a dentist. Protect mucous membranes by using a rubber dam. Make sure the Glu/Sense dentin desensitizer only comes into contact with the area to be treated.
Warning:
Avoid contact with eyes, skin, and soft tissue. If contact occurs, flush immediately with water. Extended contact with tissue can result in redness or burning. Treat like any other chemical burn.If eye contact occurs, consult a physician immediately. Do not use on patients with known sensitivities to HEMA or gluteraldehyde.
FAQs
The glutaraldehyde in GluSense “coagulates proteins” deep within the tubules. This along with the HEMA, seals the tubules and blocks outside stimuli (cold, pressure, etc) from reaching the nerve ending.
No. GluSense is effective with or without smear layer removal. The only time removal is required is if the other materials (for example, a bonding agent) used in the procedure required it.
No, avoid contact of GluSense Desensitizer with soft tissue.
No. The tooth can be moist prior to application. Desiccation of exposed dentin can contribute to sensitivity, and should be avoided. After GluSense Application, the tubules are sealed, and the tooth may be thoroughly dried if necessary.
Yes. Avoid contact with soft tissues. If contact occurs, rinse thoroughly with water.
No. Simply apply in a gentle rubbing motion for 30 seconds and dry.
Yes.
No. GluSense Desensitizer does not interfere with currently available cements.
